Side-Power SP 125 T Instalační manuál stáhnout pdf (Strana 2)

Stern tunnel installation version 1.7.2 - 2015

Installation

To achieve maximum effect, reliability and durability from your Sidepower Sternthruster, a correct installation is very

important.

Please follow the instructions carefully, and make sure that all checkpoints are carefully controlled.

1. Make sure that there are enough space both inside and outside the transom of the boat (see FIG 1).

Outside of flange:

Cut out in stern:

Bolt holes dia :

Bolt postion radius :

60°

PS !

Necessary

support

of motor.

Minimum is

hulls bottom

thickness

W.L.

FIG. 1

Stern thruster installation manual Version 1.6 - 2005

Additional considerations for positioning of stern thruster.

 Make sure that the stern-tunnel does not disturb the waterflow under the hull

 Ensure that when installed the thruster does not foul exisiting equipment inside the boat like steerage links etc.

 It is essential that the motor is supported so that the total weight is not on the tunnel alone.

 Make sure that the water flow from the thruster are not intereferred to much by sterndrives, trimtabs etc. as this

will reduce the thrust considerably.

 It is possible to mount the tunnel off the boat’s centre line if necessary.

 If the stern thickness is to much for the thruster in question you can easily remove material in the necessary area

to fit the thruster. The stern thickness even here will never have to be less than the max. measurement given as

max. stern thickness.

Measurements ref.

mm / inch

SP30Si / SP40Si SP55Si SP75Ti SP95Ti SP125Ti SP155TCi SP200TCi

SP200TCi-32 /

SP240TCi

SP285TCi

A 200mm / 7,87'' 225mm / 8,90" 312mm / 12,30" 349mm / 13,70" 363mm / 15,10" 386mm / 15,20" 419mm / 16,50" 440mm / 17,30" 404mm / 15,90"

B 190mm / 7,48'' 256mm / 10,08" 256mm / 10,08" 256mm / 10,08" 340mm / 13,39" 340mm / 13,39" 360mm / 14,20" 420mm / 16,54" 420mm / 16,54"

C 135mm / 5,31'' 150mm /5,91" 200mm / 7,87" 200mm / 7,87" 250mm / 9,84" 250mm / 9,84" 300mm / 11,81" 300mm / 11,81" 300mm / 11,81"

D 197mm / 7,76'' 337mm / 13,30" 337mm / 13,30" 337mm / 13,30" 350mm / 13,80" 350mm / 13,80" 350mm / 13,80" 456mm / 18,00" 456mm / 18,00"

E ø217mm / 8,54'' ø300mm / 11,80" ø300mm / 11,80" ø300mm / 11,80" ø300mm / 11,80" ø300mm / 11,80" 356mm / 14,02" ø396mm / 15,60" ø396mm / 15,60"

F ø160mm / 6,30'' ø200mm / 7,84" ø200mm / 7,84" ø200mm / 7,84" ø200mm / 7,84" ø200mm / 7,84" ø260mm / 11,24" ø265mm / 10,40" ø265mm / 10,40"

G 6 x ø6,5mm / 0,26'' 6x ø10,5mm / 0,41" 6x ø10,5mm / 0,41" 6x ø10,5mm / 0,41" 6x ø10,5mm / 0,41" 6x ø10,5mm / 0,41" 8x ø10,5mm / 0,41" 8x ø10,5mm / 0,41" 8x ø10,5mm / 0,41"

H ø98mm / 3,86'' ø129mm / 5,08" ø129mm / 5,08" ø129mm / 5,08" ø129mm / 5,08" ø129mm / 5,08" ø315mm / 12,40" ø345,6mm / 13,60" ø345,6mm / 13,60"

Max. Stern

thickness

14mm / 0,55'' 35mm / 1,38" 54mm / 2,13" 54mm / 2,13" 60mm / 2,36" 60mm / 2,36" 50mm / 1,97" 60mm / 2,36" 60mm / 2,36"

Measurements ref.

mm / inch

SP100HYD SP220HYD SP300HYD SP550HYD

A 158mm / 6,22" 178mm / 7,01" 208mm / 8,19" 259mm / 10,20"

B 256mm / 10,08" 340mm / 13,39" 420mm / 16,54" 570mm / 22,44"

C 200mm / 7,87" 300mm / 11,81" 300mm / 11,81" 380mm / 14,96"

D 337mm / 13,30" 350mm / 13,80" 456mm / 18,00" 550mm / 21,65"

E ø300mm / 11,80" ø300mm / 11,80" ø396mm / 15,60" ø600mm / 23,62"

F ø200mm / 7,84" ø200mm / 7,84" ø265mm / 10,40" ø400mm / 15,75"

G 6x ø10,5mm / 0,41" 6x ø10,5mm / 0,41" 8x ø10,5mm / 0,41" 12x ø13mm / 0,51"

H ø129mm / 5,08" ø129mm / 5,08" ø345,6mm / 13,60" ø530mm / 20,87"

Max. Stern

thickness

SE30/40 SE60 SE80 SE100 SE120 SE170 SE210

SH100 SH240 SP300HYD SH420/550

Measure-

ments

mm/inch

SE30/40 SE60 SE80 SE100 SE120/SE150 SE130 SE170 SE210 SP200TCi-32/

SP240TCi

SP285TCi

200mm/7.87” 225mm/8.90” 312mm/12.30” 349mm/13.70” 407mm/16.02” 363mm/15.10” 386mm/15.20” 419mm/16.50” 440mm/17.30” 404mm/15.90”

190mm/7.48” 265mm/10.08” 256mm/10.08” 256mm/10.08” 300mm/11.81” 340mm/13.39” 340mm/13.39” 360mm/14.20” 420mm/16.54” 420mm/16.54”

135mm/5.31” 150mm/5.91” 200mm/7.87” 200mm/7.87” 215mm/7.87” 250mm/9.54” 250mm/9.54” 300mm/11.80” 300mm/11.81” 300mm/11.81”

197mm/7.76” 337mm/13.30” 337mm/13.30” 337mm/13.30” 330mm/13.00” 350mm/13.80” 350mm/13.80” 350mm/13.80” 456mm/18.00” 456mm/18.00”

ø217mm/8.54” ø300mm/11.81” ø300mm/11.81” ø300mm/11.81” ø300mm/11.81” ø300mm/11.81” ø300mm/11.81” ø356mm/14.02” ø396mm/15.60” ø396mm/15.60”

ø160mm/6.3” ø200mm/7.84” ø200mm/7.84” ø200mm/7.84” ø200mm/7.84” ø200mm/7.84” ø200mm/7.84” ø260mm/11.24” ø265mm/11.40” ø265mm/11.40”

6 x

ø6,5mm/0.26”

6 x

ø10,5mm/0.41”

6 x

ø10,5mm/0.41”

6 x

ø10,5mm/0.41”

6 x

ø10,5mm/0.41”

6 x

ø10,5mm/0.41”

6 x

ø10,5mm/0.41”

8 x

ø10,5mm/0.41”

8 x

ø10,5mm/0.41”

8 x

ø10,5mm/0.41”

ø98mm/3.36” ø129mm/5.08” ø129mm/5.08” ø129mm/5.08” ø129mm/5.08” ø129mm/5.08” ø129mm/5.08” ø315mm/12.40” ø345,6/13.60” ø345,6/13.60”

Max stern

thickness

14mm/0.55” 35mm/1.38” 54mm/2.13” 54mm/2.13” 54mm/2.13” 60mm/2.36” 60mm/2.36” 50mm/1.97” 60mm/2.36” 60mm/2.36”

Measure-

ments

mm/inch

SH100 SH160 SH240 SP300HYD SH420 SH550

172mm/6.72” 172mm/6.72” 191mm/7.52” 195mm/7.68” 257mm/10.12” 257mm/10.12”

256mm/10.08” 300mm/11.81” 340mm/13.39” 420mm/16.54” 570mm/22.44” 570mm/22.44”

200mm/7.87” 215mm/7.87” 300mm/11.81” 300mm/11.81” 570mm/22.44” 570mm/22.44”

337mm/13.30” 330mm/13.00” 350mm/13.80” 456mm/18.00” 550mm/21.65” 550mm/21.65”

ø300mm/11.81” ø300mm/11.81” ø300mm/11.81” ø396mm/15.60” ø600mm/23.62” ø600mm/23.62”

ø200mm/7.84” ø200mm/7.84” ø200mm/7.84” ø265mm/11.40” ø400mm/15.75” ø400mm/15.75”

6 x

ø10,5mm/0.41”

6 x

ø10,5mm/0.41”

6 x

ø10,5mm/0.41”

8 x ø10,5mm/0.41” 12 x

ø13mm/0.51”

12 x

ø13mm/0.51”

ø129mm/5.08” ø129mm/5.08” ø129mm/5.08” ø345,6mm/13.60” ø530mm/20.87” ø530mm/20.87”

Max stern

thickness

- - - - - -

Stern thruster tunnels

Art # Product Tunnel dim Flange dim Material

90124 I SE30/40 125mm 217mm Composite

90125 I SE30/40 125mm - GRP

90052I SE60 185mm 300mm Composite

90085-2 - - GRP

90087 SE60/XF60SR 185mm 300mm GRP

90086I SE80/100 185mm 300mm Composite

90135 I SE120/150 215mm 300mm GRP

90140I SE130/170 250mm 300mm GRP

9 0150 I SE130/170 250mm 350mm Composite

9018 0I SE210 250mm 356mm GRP

90200I SP240/285 300mm 396mm GRP

90550 SH550 386mm 600mm GRP

91000 SH/SAC1000 513mm 750mm GRP

To achieve maximum effect, reliability and durability from your Sidepower Sternthruster, a correct instal-

lation is very important.

Please follow the instructions carefully, and make sure that all checkpoints are carefully controlled.

1.Make sure that there are enough space both inside and outside the transom of the boat (see

FIG 1).

Installation

Additional considerations for positioning of stern thruster.

• Makesurethatthestern-tunneldoesnotdisturbthewaterowunderthehull

• Ensure that when installed the thruster does not foul exisiting equipment inside the boat like steerage links etc.

• It is essential that the motor is supported so that the total weight is not on the tunnel alone.

• Makesurethatthewaterowfromthethrusterarenotintereferredtomuchbysterndrives,trimtabsetc.as

thiswill reduce the thrust considerably.

• It is possible to mount the tunnel off the boat’s centre line if necessary.

• If the stern thickness is to much for the thruster in question you can easily remove material in the necessary

areatotthethruster.Thesternthicknessevenherewillneverhavetobelessthanthemax.measurement

given asmax. stern thickness.

FIG. 1

1 2 3 4 5 6 7 ... 11 12

Komentáře k této Příručce

Žádné komentáře

Side-Power SP 125 T Instalační manuál Strana 2

Komentáře k této Příručce

Související produkty a manuály pro ne Side-Power SP 125 T