Side-Power SP 125 T Instalační manuál stáhnout pdf (Strana 3)

Stern tunnel installation version 1.7.2 - 2015

Installation

To achieve maximum effect, reliability and durability from your Sidepower Sternthruster, a correct installation is very

important.

Please follow the instructions carefully, and make sure that all checkpoints are carefully controlled.

1. Make sure that there are enough space both inside and outside the transom of the boat (see FIG 1).

Outside of flange:

Cut out in stern:

Bolt holes dia :

Bolt postion radius :

60°

PS !

Necessary

support

of motor.

Minimum is

hulls bottom

thickness

W.L.

FIG. 1

Stern thruster installation manual Version 1.6 - 2005

Additional considerations for positioning of stern thruster.

 Make sure that the stern-tunnel does not disturb the waterflow under the hull

 Ensure that when installed the thruster does not foul exisiting equipment inside the boat like steerage links etc.

 It is essential that the motor is supported so that the total weight is not on the tunnel alone.

 Make sure that the water flow from the thruster are not intereferred to much by sterndrives, trimtabs etc. as this

will reduce the thrust considerably.

 It is possible to mount the tunnel off the boat’s centre line if necessary.

 If the stern thickness is to much for the thruster in question you can easily remove material in the necessary area

to fit the thruster. The stern thickness even here will never have to be less than the max. measurement given as

max. stern thickness.

Measurements ref.

mm / inch

SP30Si / SP40Si SP55Si SP75Ti SP95Ti SP125Ti SP155TCi SP200TCi

SP200TCi-32 /

SP240TCi

SP285TCi

A 200mm / 7,87'' 225mm / 8,90" 312mm / 12,30" 349mm / 13,70" 363mm / 15,10" 386mm / 15,20" 419mm / 16,50" 440mm / 17,30" 404mm / 15,90"

B 190mm / 7,48'' 256mm / 10,08" 256mm / 10,08" 256mm / 10,08" 340mm / 13,39" 340mm / 13,39" 360mm / 14,20" 420mm / 16,54" 420mm / 16,54"

C 135mm / 5,31'' 150mm /5,91" 200mm / 7,87" 200mm / 7,87" 250mm / 9,84" 250mm / 9,84" 300mm / 11,81" 300mm / 11,81" 300mm / 11,81"

D 197mm / 7,76'' 337mm / 13,30" 337mm / 13,30" 337mm / 13,30" 350mm / 13,80" 350mm / 13,80" 350mm / 13,80" 456mm / 18,00" 456mm / 18,00"

E ø217mm / 8,54'' ø300mm / 11,80" ø300mm / 11,80" ø300mm / 11,80" ø300mm / 11,80" ø300mm / 11,80" 356mm / 14,02" ø396mm / 15,60" ø396mm / 15,60"

F ø160mm / 6,30'' ø200mm / 7,84" ø200mm / 7,84" ø200mm / 7,84" ø200mm / 7,84" ø200mm / 7,84" ø260mm / 11,24" ø265mm / 10,40" ø265mm / 10,40"

G 6 x ø6,5mm / 0,26'' 6x ø10,5mm / 0,41" 6x ø10,5mm / 0,41" 6x ø10,5mm / 0,41" 6x ø10,5mm / 0,41" 6x ø10,5mm / 0,41" 8x ø10,5mm / 0,41" 8x ø10,5mm / 0,41" 8x ø10,5mm / 0,41"

H ø98mm / 3,86'' ø129mm / 5,08" ø129mm / 5,08" ø129mm / 5,08" ø129mm / 5,08" ø129mm / 5,08" ø315mm / 12,40" ø345,6mm / 13,60" ø345,6mm / 13,60"

Max. Stern

thickness

14mm / 0,55'' 35mm / 1,38" 54mm / 2,13" 54mm / 2,13" 60mm / 2,36" 60mm / 2,36" 50mm / 1,97" 60mm / 2,36" 60mm / 2,36"

Measurements ref.

mm / inch

SP100HYD SP220HYD SP300HYD SP550HYD

A 158mm / 6,22" 178mm / 7,01" 208mm / 8,19" 259mm / 10,20"

B 256mm / 10,08" 340mm / 13,39" 420mm / 16,54" 570mm / 22,44"

C 200mm / 7,87" 300mm / 11,81" 300mm / 11,81" 380mm / 14,96"

D 337mm / 13,30" 350mm / 13,80" 456mm / 18,00" 550mm / 21,65"

E ø300mm / 11,80" ø300mm / 11,80" ø396mm / 15,60" ø600mm / 23,62"

F ø200mm / 7,84" ø200mm / 7,84" ø265mm / 10,40" ø400mm / 15,75"

G 6x ø10,5mm / 0,41" 6x ø10,5mm / 0,41" 8x ø10,5mm / 0,41" 12x ø13mm / 0,51"

H ø129mm / 5,08" ø129mm / 5,08" ø345,6mm / 13,60" ø530mm / 20,87"

Max. Stern

thickness

2a. Once the position for the installation has been decided, hold the tunnel in place in the horizontal position and

mark the bolt holes. Remove the tunnel and then it is possible to calculate and mark the centre (see Fig. 1).

3a.Itisimportantthatthetunnelangesitsushonthetransom.Ifnot,thettingareaonthetransomwillhaveto

beadjustedtoensureaperfectt.

PS!Takecarewithgrindersasitisveryeasytoremovetoomuchbreglass.

Now,cutoutthecentreholeandthetransomtothesameinternaldiameterasthetunnelangeand

drilltheboltholes.Beforeactualttingthesterntunnel,werecommendthatthepreparedareaissealedwith

a gelcoat or similar to ensure there is no water ingress.

4a.Beforettingthetunneltothetransom,installthegearlegtothetunnelasdescribedinthethrusterinstallation

manual.Forthrusterswithexternaloiltank,werecommendthatyouttheoilfeedpipealsobeforethetunnelis

bolted to the transom.

Special installation points described on page 7 of this manual.

5a.Whenttingthetunnel,ensuretouseanamplesealantinthesealingtracksofthe

tunnelangeandaroundtheboltstomakeawatertighttting(seeFIG.2&3).

Bolts, washers and nuts are not included as they will vary depending on the transom thickness. We

recommend A4 stainless with A4 lock nuts and A4 washers of a large diameter on both outside and inside.

Bolts diameter (stainless steel):

ø6mmor1/4”forSP30Si&SP40Si

ø10mmor3/8”forSP55Si&SP75Ti&SP95Ti&SP125Ti&SP155TCi

ø12mmor1/2”forSP200TCi&SP240TCi&SP285TCi

6a. The electromotor must have a solid support, so the weight of the motor

can not cause a twisting action on the tunnel (see FIG. 4).

7a.Refertotheinstallationmanualfortherecommendedthrustertting.

Bolt ON installation for Composite or GRP tunnels

A-A ( 1 : 2 )

A A

B B

C C

D D

E E

F F

90135i

14.04.2014

Date

1 / 1

Edition Sheet

Kurt Skage

Material Type

GRP

Drawing nr

Borremal for Hekktunnel SE120-150 (2)

Part nr

Size

Scale

Title

Hekktunnel

Tolerance

NS-ISO 2768-1

SLEIPNER MOTOR AS

3,170 kg

Weight

SE120-150

305



215



147



114

R22

R16

133,3

330

NS-ISO 2768-1

Over t.o.m. f m c v

0,5 3

±0,05 ±0,1 ±0,2 -

3 6 ±0,05 ±0,1 ±0,3 ±0,5

6 30 ±0,1 ±0,2 ±0,5 ±1

30 120 ±0,15 ±0,3 ±0,8 ±1,5

120 400 ±0,2 ±0,5 ±1,2 ±2,5

400 1000 ±0,3 ±0,8 ±2 ±4

1000 2000 ±0,5 ±1,2 ±3 ±6

2000 4000 - ±2 ±4 ±8

REVISION HISTORY

Revidert av:

REV DESCRIPTION DATE

Kurt

Skage

A 13.12.2007

FIG. 2

FIG. 4FIG. 3

Motor

support

MUST be

installed!

Sealant

1 2 3 4 5 6 7 8 ... 11 12

Komentáře k této Příručce

Žádné komentáře

Side-Power SP 125 T Instalační manuál Strana 3

Komentáře k této Příručce

Související produkty a manuály pro ne Side-Power SP 125 T